Mopar Firing Orders & Torque Specs
Mopar Firing Orders & Torque Specs
Firing order, cylinder numbering, distributor rotation and factory torque specs for classic Chrysler, Dodge and Plymouth engines. Specs are for stock fasteners with oiled threads. Where references disagree, we show both.
Firing order, cylinder numbers & distributor rotation
Every classic Mopar V8 uses the same firing order:
1-8-4-3-6-5-7-2
Cylinder numbering: 1-3-5-7 on the driver side and 2-4-6-8 on the passenger side, front to back. Cylinder 1 is the front cylinder on the driver side.
| Engine family | Distributor location | Rotor turns |
|---|---|---|
| LA small block: 273, 318, 340, 360 | Rear of the engine | Clockwise |
| B / RB big block: 361, 383, 400, 413, 426 wedge, 440 | Front of the engine | Counterclockwise |
| 426 Hemi | Front of the engine | Counterclockwise |
| Slant six: 170, 198, 225 | Side of the block | Clockwise (per enthusiast references). Firing order 1-5-3-6-2-4 |
Wiring the cap: bring cylinder 1 up to top dead center on the compression stroke, note which cap tower the rotor points at, and make that the #1 wire. Then follow 1-8-4-3-6-5-7-2 around the cap in the direction the rotor turns.
273 / 318 / 340 / 360 (LA small block)
| Fastener | Torque | Notes |
|---|---|---|
| Cylinder head bolts, 273 & 318 | 85 ft-lb | Tighten in steps, following the factory sequence |
| Cylinder head bolts, 340 & 360 | 95 ft-lb | Conflict: a 1968 service manual lists 85 ft-lb for the 340. One older manual says 85 with steel shim gaskets and 95 with composition gaskets |
| Main bearing caps | 85 ft-lb | |
| Connecting rod nuts | 45 ft-lb | Stock rod bolts only. Aftermarket (ARP etc.) rod bolts use the maker's spec |
| Intake manifold | 35 ft-lb | |
| Rocker shaft bolts | 200 in-lb (about 17 ft-lb) | Per the factory service manual. 30 ft-lb is a common mistake you will see online |
| Camshaft sprocket lock bolt | 35 ft-lb | |
| Vibration damper (crank) bolt | 100–135 ft-lb | Conflict: a 1971 manual lists 100 ft-lb; another factory list gives 135 ft-lb |
| Flywheel / flexplate to crank | 55 ft-lb | |
| Water pump to block | 30 ft-lb | |
| Fuel pump to block | 30 ft-lb | |
| Oil pump to block | 30 ft-lb | |
| Oil pump cover | 95 in-lb | |
| Carburetor to manifold nuts | 7 ft-lb |
383 / 400 / 440 (B and RB big block)
| Fastener | Torque | Notes |
|---|---|---|
| Cylinder head bolts | 70 ft-lb | Tighten in steps (for example 40, 55, 70) following the factory sequence |
| Main bearing caps | 85 ft-lb | |
| Connecting rod nuts | 45 ft-lb | One reference lists 55 ft-lb for heavy-duty rods |
| Camshaft sprocket lock bolt | 35 ft-lb | |
| Timing chain cover bolts | 15 ft-lb | |
| Spark plugs | 30 ft-lb | 14 mm gasket-seat plugs in iron heads |
| Carburetor to manifold nuts | 7 ft-lb |
Values from Chrysler's 1969 factory training material for the 383 and 440.
426 Hemi
The 426 Hemi uses the same 1-8-4-3-6-5-7-2 firing order and cylinder numbering as the other Mopar V8s, and its distributor turns counterclockwise. Its main caps are cross-bolted through the sides of the block, so the torque procedure is different from the wedge engines.
Slant six (170 / 198 / 225)
Firing order 1-5-3-6-2-4, cylinders numbered 1 to 6 from the front.
| Fastener | Torque | Notes |
|---|---|---|
| Cylinder head bolts | 70 ft-lb | Per enthusiast references; check your service manual |
| Main bearing caps | 85 ft-lb | |
| Connecting rod nuts | 45 ft-lb |
Working on your Mopar?
Mopar partsEngineElectrical & WiringCoolingHardware
More Mopar tools: VIN & fender tag decoder · Paint codes · Production numbers
Frequently asked questions
What is the firing order for a 318, 360 or 440?
Which way does a Mopar distributor turn?
Where is cylinder number 1 on a Mopar V8?
Is the 340 head bolt torque 85 or 95 ft-lb?
What is the rocker shaft bolt torque on a small block Mopar?
Compiled from Chrysler factory service manual values and factory training material as quoted by Mopar enthusiast references, cross-checked against cylinder head makers' instructions. Not affiliated with Stellantis or Chrysler.