Install How-Tos
Install How-Tos
Step-by-step help for common restoration jobs. Always follow any instructions that come with your part, because they take priority over these general steps.
Work safely. Wear eye protection, use adhesives and cleaners with good ventilation, and disconnect the battery before any electrical work. If a job involves brakes, steering, suspension or fuel, have it checked by a qualified mechanic if you're unsure.
How-tos on this page
1. Replacing door weatherstrip
You'll need
New weatherstrip, the correct clips or retainers, weatherstrip adhesive, adhesive remover, a plastic trim tool, rags and masking tape.
Steps
- Before you remove the old seal, note how it's held on (clips, glue or both) and where it starts and ends. Take photos.
- Remove the old seal with a plastic trim tool so you don't scratch the paint. Pop out any clips carefully.
- Clean the channel completely. Take off the old adhesive with remover, then wipe with a clean rag. New adhesive won't hold on old glue or dirt.
- Dry-fit the new seal. Lay it in place without glue, start at the factory starting point, and check that the clip holes line up and that it isn't stretched or bunched at the corners.
- Glue in short sections. Apply a thin bead of weatherstrip adhesive to the channel and to the seal, let it go tacky as the adhesive's directions say, then press the seal in. Work a section at a time, and use masking tape to hold it while it sets.
- Install the clips (if used) as you go.
- Let it cure before slamming the door. Close the door gently and leave it closed overnight so the seal sets in position.
- Check for leaks with a hose once it's cured, and adjust the door striker only if needed.
New seals are thicker than worn ones. A door that closes hard at first is normal and usually eases up after a few weeks.
2. Installing emblems
- Check the mounting type of your new emblem: studs with speed nuts, clips, or adhesive tape.
- Remove the old emblem. Stud emblems come off from behind the panel by removing the nuts (you may need to remove an interior or trunk panel). For taped emblems, warm them gently with a hair dryer and slide fishing line behind them to cut the tape.
- Clean the area. Remove old tape residue with adhesive remover, then wipe with isopropyl alcohol.
- Position it. For stud emblems, use the existing holes. For taped emblems, mark the position with masking tape first, using a photo or measurements from the other side of the car.
- Install it. Push the studs through and secure them with new speed nuts by hand (don't overtighten them or the studs can break). For taped emblems, peel the backing and press firmly for 30 seconds.
- Taped emblems: avoid washing the car for 24–72 hours while the adhesive cures.
3. Replacing a tail lamp or marker lens
- Disconnect the battery if you'll be unplugging any sockets.
- Find the fasteners. Many lenses come off from outside with screws. Others mount from inside the trunk with nuts on studs.
- Remove the lens and old gasket. Clean the housing and check the sockets for corrosion. Clean the contacts or replace the sockets if needed.
- Fit the new gasket before the lens. A new gasket keeps water and dust out.
- Install the lens and tighten the screws or nuts evenly and gently. Plastic lenses crack if you overtighten them.
- Reconnect and test the running lights, brake lights and turn signals before you put the trunk panels back.
4. Applying a vinyl stripe or decal
- Work in the shade at roughly 60–80°F. Vinyl won't stick well in the cold, and it stretches too easily in the heat.
- Clean the surface with soap and water, then wipe with isopropyl alcohol. Don't wax the area beforehand.
- Position it with tape. Lay the stripe in place with its backing still on and use masking tape to make a hinge along one edge. Measure from body lines on both sides of the car so it's even.
- Apply it. Fold back half, peel the backing, and squeegee from the center outward. Then do the other half. For large stripes, a light mist of water with a drop of baby shampoo lets you slide it into place before squeegeeing.
- Remove the top transfer tape (if there is one) slowly, pulling back flat against itself.
- Prick any bubbles with a fine pin and press them flat. Avoid washing for a few days.
Frequently asked questions
Why is my door hard to close after new weatherstrip?
New seals are thicker than worn ones, so a door that closes hard at first is normal. It usually eases up after a few weeks. Close the door gently and leave it closed overnight after installing so the seal sets in position.
How do I remove an emblem that's held on with tape?
Warm it gently with a hair dryer and slide fishing line behind it to cut the tape. Then remove the residue with adhesive remover and wipe the area with isopropyl alcohol before installing the new one.
What temperature is best for applying a vinyl stripe?
Work in the shade at roughly 60–80°F. Vinyl won't stick well in the cold and stretches too easily in the heat.
How long should I wait to wash the car after installing emblems or stripes?
Wait 24–72 hours after installing taped emblems, and a few days after applying stripes or decals, so the adhesive can cure.
Not sure which part you need? See our buying & fitment guides or email customerservice@joltparts.com.