Rear Axle Codes & Rear End Identification
Rear Axle Codes & Rear End Identification
Find out what gear ratio and differential your car left the factory with. Decode a Camaro, Nova, Firebird or Olds Cutlass/4-4-2 axle code below, use our Chevelle, El Camino & Monte Carlo axle code decoder, identify a Mopar 8 3/4, or use the ratio calculator for anything else. Where references disagree, the result says so.
Camaro & Nova axle code decoder
Where to look: the code is stamped on the front face of the passenger-side axle tube, near the middle on most 1965-79 cars (1962-63 Chevy II: front right of the carrier; 1964: bottom of the carrier). Clean it with a wire brush or lacquer thinner. Through 1970 it reads code, month, day, plant, shift (for example BV 0315 G1); from 1971 it reads code, plant, day of the year. A letter on a second line (D, E or W) shows who made the Positraction unit.
Firebird & Oldsmobile axle code decoder
- Firebird: a two-letter code (three letters on 1970 cars) stamped on the front of the passenger-side axle tube, left of the carrier. One 1967 Pontiac service supplement puts it on the rear of the left tube, so check both. From 1970 Firebirds used Chevrolet-built axles, which is why the codes look like Chevy codes.
- Oldsmobile: a two-letter code about 3/8 in. tall stamped on the passenger-side tube, usually on the inboard side and often upside down, roughly a foot in from the brake backing plate. 1970 Olds codes here are a partial list (4-4-2 and W-30 codes only).
- Pontiac GTO, LeMans and full-size, and Buick: full code lists for these aren't published in a form we could confirm, so they're not in the decoder yet. Use the ratio calculator below.
Mopar 8 3/4 rear end identification
The Chrysler 8 3/4 in. has a round rear housing with no bolt-on cover; the center section comes out the front. The last three digits of the carrier casting number, cast on the lower driver side, tell you which version it is.
| Version | Pinion stem | Carrier casting numbers | How to spot it | Notes |
|---|---|---|---|---|
| 741 | 1 3/8 in. small stem | 1820657 (1957–64), 2070741 | Large X cast on the left side | One reference lists the 741 for 1964–72, another 1965–74. Generally rated the weakest of the three. |
| 742 | 1 3/4 in. large stem | 1634985 (1957–64), 2070742 | Large 2 cast on the left side | One reference lists about 1961–69, another 1957–68. |
| 489 | 1 7/8 in. tapered stem | 2881488, 2881489 | Large 9 cast on the left side | Introduced in 1969 and phased in through 1970; used through 1974. |
- Ratio: through 1965 the ratio was stamped on the carrier's identification boss, with an S if Sure Grip. After 1965 a small metal tag under one of the carrier nuts shows the ratio. Tags are often missing, so use the calculator.
- Sure Grip: Chrysler's limited slip, optional on the 8 3/4 from 1958 to 1974. A Sure Grip lube tag was sometimes added, and later cars sometimes had the fill plug painted orange.
- 8 1/4 and Dana 60: both have a bolt-on rear cover. The 8 1/4 replaced the 8 3/4 in 1973 A-bodies (Dart, Valiant, Duster). The Dana 60 is much larger, with a 10-bolt cover.
Gear ratio calculator
Method 1, count the turns: jack up both rear wheels, put the transmission in neutral, mark the tire and the driveshaft, and turn both tires one full turn together. Count the driveshaft turns.
Method 2, count the teeth (with the cover off):
Identify any classic rear end
| Make | Where the codes are | Quick ID tips |
|---|---|---|
| Chevrolet (Camaro, Chevelle, Nova, Impala) | Ratio code on the passenger axle tube, front side | Count the cover bolts: 10 or 12. The 1964-72 car 12-bolt has an 8.875 in. ring gear; the Chevy 10-bolt of that era has an 8.2 in. ring gear. Casting numbers on the carrier confirm it. |
| Pontiac, Oldsmobile, Buick | Two- or three-letter ratio code on an axle tube (see the decoder above for Firebird and Olds) | These divisions built their own 10-bolt (8.2 in. and later 8.5 in.) and 12-bolt rear ends that look similar to Chevy units but don't share every part. Some 1970 Pontiac A-bodies and Canadian-built 1970 Buick GS cars used Chevrolet-style 12-bolts. |
| Mopar (Dodge, Plymouth) | Ratio tag under a carrier nut (after 1965), or stamped on the carrier boss (through 1965) | See the 8 3/4 table above. The 8 1/4 and Dana 60 have a bolt-on rear cover; the Dana 60 cover has 10 bolts and the housing is much bigger. |
Posi or not? With both rear wheels off the ground and the transmission in neutral, turn one tire by hand. If the other tire turns the same direction, it's a Positraction/limited slip. If it turns the opposite way, it's an open differential.
Rebuilding the rear end?
CamaroNovaChevelleFirebirdCutlass & 4-4-2MoparSuspensionBrakesHardware
Frequently asked questions
Where is the rear axle code on a Camaro or Nova?
What does axle code ZE mean on a 1969 Firebird?
How do I tell a 741, 742 or 489 Mopar rear end apart?
How do I tell a 10-bolt from a 12-bolt?
How can I find my gear ratio without a code?
How do I know if I have Positraction?
Camaro codes compiled from the Camaro Research Group's axle code research; Nova codes from Nova enthusiast references, which note their list is compiled from many sources and may be incomplete. Firebird codes from second-generation Trans Am and first-generation Firebird enthusiast references; Oldsmobile codes from an Olds club's technical library; Mopar 8 3/4 details from Mopar enthusiast references. Not affiliated with General Motors or Stellantis.