GM Firing Orders, Torque Specs & Spark Plugs

← Tech Center

GM Firing Orders, Torque Specs & Spark Plugs

Firing orders and distributor rotation for classic GM engines, factory torque specs for Chevrolet, Oldsmobile and Buick V8s (plus the Buick V6), and the original spark plugs and gaps for 1968–72 Chevrolets. Pontiac torque specs are on our Pontiac engine page.

Jump to

Open all Β· Close all

Firing orders & distributor rotationall GM
FRONT (radiator) Driver side Passenger side 13572468 V8 (top view)

How GM numbers V8 cylinders: odd numbers (1-3-5-7) are on the driver side, front to back, and even numbers (2-4-6-8) are on the passenger side. Cylinder 1 is the front cylinder on the driver side.

Wiring the cap: bring the engine to top dead center on the compression stroke for cylinder 1, note where the rotor points, and put cylinder 1's wire in that tower. Then work around the cap in the direction the rotor turns, following the firing order.

Engine Firing order Distributor rotation (from above)
Chevrolet small-block V8 (262, 265, 283, 302, 305, 307, 327, 350, 400) 1-8-4-3-6-5-7-2 Clockwise
Chevrolet big-block V8 (396, 402, 427, 454) 1-8-4-3-6-5-7-2 Clockwise
Pontiac V8 (301, 326, 350, 389, 400, 428, 455) 1-8-4-3-6-5-7-2 Counterclockwise
Oldsmobile V8 (260, 307, 330, 350, 400, 403, 425, 455) 1-8-4-3-6-5-7-2 Counterclockwise
Buick V8 (300, 340, 350, 400, 430, 455; not the earlier "nailhead") 1-8-4-3-6-5-7-2 Clockwise
Chevrolet inline six (230, 250, 292) 1-5-3-6-2-4 (cylinder 1 at the front) Clockwise
Chevrolet 4.3 / 262 V6 1-6-5-4-3-2 (1-3-5 driver side, 2-4-6 passenger side) Clockwise
Later GM LS-series V8 (for reference) 1-8-7-2-6-5-4-3 No distributor
The firing order is the same for most classic GM V8s, but Pontiac and Oldsmobile distributors turn the opposite way from Chevrolet. That's the most common plug-wire mistake on an engine swap. Some aftermarket camshafts change the firing order, so check your cam card.
Use torque specs as a reference only. These are factory values for original-style bolts with clean, oiled threads. Aftermarket bolts and studs (such as ARP) have their own specs, so always follow the fastener maker's instructions. Use sealer on head bolts that go into the water jacket, torque in three even steps, and follow the correct tightening sequence. Confirm with the factory service manual for your exact engine.
Chevrolet small-block V8262–400
Fastener Torque (ft-lb)
Main caps, 7/16 in. (inner bolts) 70
Main caps, 7/16 in. outer bolts (4-bolt blocks) 65
Main caps, 3/8 in. outer bolts 40
Connecting rods, 3/8 in. bolts 40–45
Connecting rods, 11/32 in. bolts (early engines) 38–44
Cylinder head bolts 65
Rocker studs, screw-in 50
Intake manifold (iron heads) 30
Oil pump to main cap 60–70
Cam sprocket bolts 18–20
Harmonic balancer bolt 60
Flywheel / flexplate 60–65
Pressure plate 35
Bellhousing 25
Exhaust manifold 20–25
Chevrolet big-block V8396 / 402 / 427 / 454
Fastener Torque (ft-lb)
Main caps, 2-bolt (396–427) 95
Main caps, 4-bolt (inner and outer) 110
Connecting rods, 3/8 in. bolts 50
Connecting rods, 7/16 in. bolts 67–73
Cylinder head bolts, long 75
Cylinder head bolts, short 65–68
Rocker studs, screw-in 50
Intake manifold (iron heads) 25–30
Oil pump 65
Cam sprocket bolts 20
Harmonic balancer bolt 85
Flywheel / flexplate 60–65

Some references list 80 ft-lb for all big-block head bolts. Most list 75 long and 65–68 short, as shown, so use your head bolt maker's figure.

Oldsmobile V8330 / 350 / 400 / 425 / 455
Fastener Torque (ft-lb) Notes
Main caps, 400 / 425 / 455 120
Main caps, 330 80 (caps 1–4), 120 (cap 5)
Cylinder head bolts 80 Clean and dip the whole bolt in engine oil first. One Oldsmobile service manual lists 85 for some later 350 blocks, so check yours.
Connecting rod nuts 42
Rocker arm studs to head 35
Intake manifold 35 Oiled bolts
Exhaust manifold 25
Oil pump to main cap 35
Carburetor to intake 15
Water pump to front cover 13

Values are for 1964–71 era 330, 350, 400, 425 and 455 engines. The later 260, 307 and 403 used some different specs (rebuilders quote 95 ft-lb on 403 head bolts), so confirm with the service manual for 1977-and-later engines.

Buick big-block V8400 / 430 / 455
Fastener Torque (ft-lb) Notes
Cylinder head bolts 100–120 Retorque was specified after warm-up
Main bearing caps 80–115
Connecting rods 45–50
Harmonic balancer bolt 200 minimum
Flywheel / flexplate 60
Intake manifold 455: 55 Β· 400/430: 50
Exhaust manifold 18
Rocker arm shaft to head 455: 25 Β· 400/430: 30
Timing chain cover 455: 29 Β· 400/430: 30
Oil pan 14
Motor mount to block 455: 63 Β· 400/430: 70
Buick 300 / 340 / 350 V8 & 225 V6small-block
Fastener 300 / 340 / 350 V8 225 V6
Cylinder head bolts 65–80 (use the high end on the 350) 65–80
Main bearing caps 95–120 (350 manual: 95) 95–120
Connecting rods 30–40 (350 manual: 35) 30–40
Harmonic balancer bolt 140 minimum 140–160
Flywheel / flexplate 50–65 50–65
Intake manifold 45–55
Exhaust manifold 15–20
Original spark plugs & gaps1968–1972 Chevrolet
Year Engine Original AC plug
1968 194 / 230 six R46N
1968 307 R45S
1968 327 R44 (some lists show 44)
1968 396 R43N or R44N
1969 230 / 250 six R46N
1969 307 R45S
1969 350 R44
1969 396 R43N (see note)
1970 250 six R46T
1970 307 R45
1970 350 R44
1970 396 / 402 R44T (see note)
1970 454 R43T
1971 250 six R46TS
1971 307 and 350 2-bbl (L65) R45TS
1971 350 4-bbl (L48) and 402 R44TS
1971 454 (LS5) R43TS
1972 250 six R46T
1972 All V8s R44T
Reading an AC plug number: the number is the heat range (higher = hotter), T = tapered seat (no gasket), S = extended tip, N = flat seat with a gasket. Never put a tapered-seat plug in a gasket-seat head or the other way around. Big-block note: early in 1970 Chevrolet recast the 3964290 head for tapered-seat plugs, so early castings may still take the flat-seat R43N.
Ignition Typical gap
Points ignition (most 1974 and earlier) 0.035 in.
HEI ignition (1975 and later, or an HEI swap) 0.045 in.

Factory lists are for Chevelle-family cars and match most Chevrolet passenger cars of the same years. Many owners run one heat range hotter (for example R45TS instead of R44T) on today's fuel to reduce fouling.

Frequently asked questions

What is the firing order for a small-block Chevy 350?
1-8-4-3-6-5-7-2, with the distributor turning clockwise (viewed from above). Odd cylinders are on the driver side and even cylinders on the passenger side, with cylinder 1 at the front on the driver side.
Do Pontiac and Oldsmobile V8s use the same firing order as Chevrolet?
Yes, 1-8-4-3-6-5-7-2, but their distributors turn counterclockwise, the opposite way from Chevrolet. That's the most common plug-wire mistake on an engine swap.
What is the head bolt torque on a small-block Chevy?
65 ft-lb with factory-style bolts and clean, oiled threads, tightened in three even steps in the correct sequence. Aftermarket bolts and studs have their own specs, so follow the maker's figure.
What spark plug gap should I use?
About 0.035 in. for points ignition (most 1974 and earlier engines) and about 0.045 in. for HEI ignition (1975 and later, or an HEI swap).
What does the T mean in an AC spark plug number like R44T?
T means a tapered seat with no gasket. N means a flat seat with a gasket, and S means an extended tip. The number is the heat range, and a higher number is hotter. Never mix tapered-seat and gasket-seat plugs and heads.

Parts for the job

EngineIgnition & WiringHardwareCooling

More engine info: GM engine code lookup Β· GM casting numbers Β· Quadrajet number lookup Β· Pontiac engine codes & torque

Firing orders cross-checked against several published ignition references. Torque values come from factory service manual figures as published by Buick, Oldsmobile and Chevrolet clubs and engine-build references; where they disagree we show the range. Spark plug list from Chevelle restoration references. Not affiliated with General Motors.