Mopar Firing Orders & Torque Specs

← Tech Center

Mopar Firing Orders & Torque Specs

Firing order, cylinder numbering, distributor rotation and factory torque specs for classic Chrysler, Dodge and Plymouth engines. Specs are for stock fasteners with oiled threads. Where references disagree, we show both.

Firing order, cylinder numbers & distributor rotation

Every classic Mopar V8 uses the same firing order:

1-8-4-3-6-5-7-2

Cylinder numbering: 1-3-5-7 on the driver side and 2-4-6-8 on the passenger side, front to back. Cylinder 1 is the front cylinder on the driver side.

Engine family Distributor location Rotor turns
LA small block: 273, 318, 340, 360 Rear of the engine Clockwise
B / RB big block: 361, 383, 400, 413, 426 wedge, 440 Front of the engine Counterclockwise
426 Hemi Front of the engine Counterclockwise
Slant six: 170, 198, 225 Side of the block Clockwise (per enthusiast references). Firing order 1-5-3-6-2-4

Wiring the cap: bring cylinder 1 up to top dead center on the compression stroke, note which cap tower the rotor points at, and make that the #1 wire. Then follow 1-8-4-3-6-5-7-2 around the cap in the direction the rotor turns.

273 / 318 / 340 / 360 (LA small block)
Fastener Torque Notes
Cylinder head bolts, 273 & 318 85 ft-lb Tighten in steps, following the factory sequence
Cylinder head bolts, 340 & 360 95 ft-lb Conflict: a 1968 service manual lists 85 ft-lb for the 340. One older manual says 85 with steel shim gaskets and 95 with composition gaskets
Main bearing caps 85 ft-lb
Connecting rod nuts 45 ft-lb Stock rod bolts only. Aftermarket (ARP etc.) rod bolts use the maker's spec
Intake manifold 35 ft-lb
Rocker shaft bolts 200 in-lb (about 17 ft-lb) Per the factory service manual. 30 ft-lb is a common mistake you will see online
Camshaft sprocket lock bolt 35 ft-lb
Vibration damper (crank) bolt 100–135 ft-lb Conflict: a 1971 manual lists 100 ft-lb; another factory list gives 135 ft-lb
Flywheel / flexplate to crank 55 ft-lb
Water pump to block 30 ft-lb
Fuel pump to block 30 ft-lb
Oil pump to block 30 ft-lb
Oil pump cover 95 in-lb
Carburetor to manifold nuts 7 ft-lb
Later Magnum engines (1992 and up) use different specs, such as 105 ft-lb head bolts. This table is for the classic LA engines.
383 / 400 / 440 (B and RB big block)
Fastener Torque Notes
Cylinder head bolts 70 ft-lb Tighten in steps (for example 40, 55, 70) following the factory sequence
Main bearing caps 85 ft-lb
Connecting rod nuts 45 ft-lb One reference lists 55 ft-lb for heavy-duty rods
Camshaft sprocket lock bolt 35 ft-lb
Timing chain cover bolts 15 ft-lb
Spark plugs 30 ft-lb 14 mm gasket-seat plugs in iron heads
Carburetor to manifold nuts 7 ft-lb

Values from Chrysler's 1969 factory training material for the 383 and 440.

426 Hemi

The 426 Hemi uses the same 1-8-4-3-6-5-7-2 firing order and cylinder numbering as the other Mopar V8s, and its distributor turns counterclockwise. Its main caps are cross-bolted through the sides of the block, so the torque procedure is different from the wedge engines.

Hemi torque specs: not fully documented here. We could not confirm a full set of 426 Hemi factory torque values from two independent sources, so we are not listing them. Use the factory service manual for your year.
Slant six (170 / 198 / 225)

Firing order 1-5-3-6-2-4, cylinders numbered 1 to 6 from the front.

Fastener Torque Notes
Cylinder head bolts 70 ft-lb Per enthusiast references; check your service manual
Main bearing caps 85 ft-lb
Connecting rod nuts 45 ft-lb
Always check: these are stock values for stock fasteners. Aftermarket heads, bolts and studs (Edelbrock, ARP and others) come with their own specs. Use theirs.

Working on your Mopar?

Mopar partsEngineElectrical & WiringCoolingHardware

More Mopar tools: VIN & fender tag decoder · Paint codes · Production numbers

Frequently asked questions

What is the firing order for a 318, 360 or 440?
1-8-4-3-6-5-7-2. Every classic Mopar V8 uses it, including the 340, 383 and 426 Hemi.
Which way does a Mopar distributor turn?
Small blocks (273, 318, 340, 360) turn clockwise. Big blocks (383, 400, 440) and the 426 Hemi turn counterclockwise.
Where is cylinder number 1 on a Mopar V8?
The front cylinder on the driver side. The driver side is 1-3-5-7 and the passenger side is 2-4-6-8.
Is the 340 head bolt torque 85 or 95 ft-lb?
Most factory references give 95 ft-lb for the 340 and 360 and 85 for the 273 and 318. A 1968 manual lists 85 for the 340. Check the manual for your year and the instructions with your head gasket.
What is the rocker shaft bolt torque on a small block Mopar?
200 inch-pounds (about 17 ft-lb) per the factory service manual. You will often see 30 ft-lb online, which is too much for stock bolts.

Compiled from Chrysler factory service manual values and factory training material as quoted by Mopar enthusiast references, cross-checked against cylinder head makers' instructions. Not affiliated with Stellantis or Chrysler.