Transmission Identification Guide (GM & Mopar)
Transmission Identification Guide
Figure out which transmission is in your classic GM or Mopar without pulling it. For automatics, the pan shape and the number of pan bolts tell you almost everything. For manual 4-speeds, look at the case material, the side cover and where the reverse lever sits. Then confirm with the ID tag or stamped code.
Quick finder: count the pan bolts
GM automatic transmissions
| Transmission | Pan bolts | Pan shape | Other clues |
|---|---|---|---|
| Powerglide (2-speed) | 14 | Sideways rectangle | Often has POWERGLIDE cast into the case. Chevrolet's 2-speed; Buick and Oldsmobile used their own 2-speeds (Super Turbine 300, Jetaway) before the Turbo Hydra-Matic took over |
| TH350 (3-speed) | 13 | Nearly square with one angled corner | Vacuum modulator; kickdown by cable. Ratios 2.52, 1.52, 1.00 |
| TH400 (3-speed) | 13 | Irregular, bulges on the passenger side (often called the Texas shape) | Vacuum modulator; electric kickdown switch instead of a cable |
| TH200 / 200C (3-speed) | 11 | Small rectangle, similar to a TH350 | Metric unit; lighter duty |
| 200-4R (4-speed overdrive) | 16 | Long, irregular | Ratios 2.74, 1.57, 1.00, 0.67 |
| 700R4 / 4L60 / 4L60E (4-speed overdrive) | 16 | Rectangle with rounded corners | No vacuum modulator; longer than a TH350 (about 30 in.). Ratios 3.06, 1.63, 1.00, 0.70. The electronic 4L60E has the same pan |
| 4L80E (4-speed overdrive) | 17 | Very large rectangle | Heavy-duty electronic unit; later trucks |
The ID tag: most Turbo Hydra-Matics carry a stamped code or tag that shows the model year, a two-letter application code and the build date. The application code links the transmission to the engine and car it was built for.
GM 4-speed manuals
| Transmission | Case | Side cover | Reverse lever |
|---|---|---|---|
| Muncie (M20, M21, M22) | Aluminum, with aluminum tail housing | 7 bolts | In the tail (extension) housing |
| Saginaw | Cast iron (aluminum on some later units) | 7 bolts | In the side cover |
| Borg-Warner T10 / Super T10 | Cast iron or aluminum | 9 bolts | In the tail housing |
Which Muncie? M20 is the wide-ratio box, M21 the close-ratio and M22 the heavy-duty close-ratio (the Rock Crusher). On 1969–72 units the date code often ends in a letter for the model: A = M20, B = M21, C = M22, but it is not always stamped. The only sure way to spot an M22 is to remove the side cover and look for its straighter-cut gears.
Mopar transmissions
| Transmission | How to spot it |
|---|---|
| A904 TorqueFlite (3-speed automatic) | Squarish pan with one angled corner and a fairly straight passenger-side pan rail. Used behind the slant six and many small blocks |
| A727 TorqueFlite (3-speed automatic) | Similar pan, but with an extra bulge (kick-out) on the passenger side where the dipstick tube enters. Heavier-duty; used behind the big blocks and Hemi as well as some small blocks |
| A833 (4-speed manual) | Mopar's New Process 4-speed, used in the muscle car era |
Shop drivetrain parts
Transmission & ClutchShift knobs & InteriorHardware
More tools: Rear axle codes & ratio calculator · GM engine codes · Mopar specs
Frequently asked questions
How do I tell a TH350 from a TH400?
How many pan bolts does a 700R4 have?
How can I tell a Muncie from a Saginaw?
How do I tell a 727 from a 904?
Compiled from GM and Mopar enthusiast and restoration references and transmission builders' ID guides, cross-checked. Not affiliated with General Motors or Stellantis.